Please contact your dealer for further information. Ford may change the contents without notice and without incurring obligation. Remove the outboard rubber boot from the lamp assembly by pulling rearward. Wrap the clear tube around the compressor housing. Pull up on the handle and push the floor panel into place. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Fold the edges of the vinyl towards the center, making sure that the edges clear the end cap slots. For the non-step style plug socket, the hole is the same size in the front of the plug socket as it is at the back bottomed out in the socket hole end of the plug socket. A cassette deck loading mechanism pulls the tape in the rest of the way. They are committed to meeting your service needs and to assuring your continuing satisfaction. At the back of the headlamp, pry up and remove the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward.
If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. All of Chilton's online content for the 2001 Ford Taurus is updated monthly, so you'll have the most recent information on hand for any Do-It-Yourself project. Step Style - If you look inside the connector on the Camshaft Position Sensor; you are looking at the socket female side of a quick connect plug. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. You can also use the message center to program the autolamp exit time delay. Check your Warranty Guide to find out which parts and services are covered. I haven't been able to find one.
After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about five seconds after pumping fuel before removing the fuel filler nozzle. Do not tow with a slingbelt. Without releasing the HomeLink button, follow Step 1 in the Programming section. Position the child safety seat in a seat with a combination lap and shoulder belt. Check the fuel filler cap for proper installation. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. If the side air bag has deployed, the air bag will not function again.
If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter. Plug the power cable into the 12V power point in the vehicle. Fold the edges of the vinyl towards the center, making sure that the edges clear the end cap slots. Tighten the bolts to 26 ft-lbs 35 Nm. Be careful not to crimp the filter element edges between the air filter housing and cover. Note: You cannot immediately start your vehicle from the on mode. Your primary responsibility is the safe operation of the vehicle.
Buckle the combination lap and shoulder belt. The remote entry system activates the illuminated entry feature; this feature turns on the lamps for 25 seconds or until the ignition is turned The battery saver feature will turn off the lamps 10 minutes after the ignition is turned off. See Active park assist in the Driving chapter for more information. Installation of the sealant canister to the temporary mobility kit 1. Combination lap and shoulder belts 1. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.
The emission system heats up the engine compartment and exhaust system, which can start a fire. Your transaxle does not consume fluid. In such conditions, the manual override may be used to turn the high beams on or off. To adjust cross-bar position: 1. You can activate the intelligent access feature as long as you have one of your intelligent access keys within range of the driver door or the trunk.
Start the engine of the disabled vehicle. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. For questions or comments, contact HomeLink at www. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Replace the two screws retaining the cowl top inner panel shield.
Note: Do not wipe off any grease on the battery terminals on the back surface of the circuit board. Connect the other end of the positive + cable to the positive + terminal of the assisting battery. The indicator light will begin to flash after 20 seconds. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. The fuel fill inlet may not have been properly closed.
Consult the engine block heater section for proper use of the engine block heater. The system will revert to chime on each time the vehicle is started. Contact your authorized dealer as soon as possible. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. I will buy all over again.